Ruptela - Installation Guide
Installing a GPS tracking device in your vehicle will not be a sophisticated job, however it is crucial to take safety precautions, as such the installation should solely be carried out by a qualified Auto Electrician. Usually, it takes approximately 2 hours to set it up depending on the complexity of the vehicle’s wiring construction. GPS machine installation (basic installation with no gas/temperature/door iTagPro smart tracker sensors related), learn the following instructions. Read extra on the Do’s & Dont’s of GPS gadget installation at the top of this doc. Screwdriver set, Plier, Multimeter and Wire Stripper/Cutter/Crimper. Before putting in the system, you want to notice down International Mobile Equipment Identity (IMEI) variety of the GPS tracking device and the SIM GSM number. Then insert the GPRS enabled SIM card to the machine. You could as effectively obtain the vehicle addition template to document car data. Then insert the GPRS enabled SIM card to the gadget.
You could as well download the vehicle addition template to document automobile info. IMEI is a unique number to identify GSM, WCDMA, and iDEN mobile phones, satellite phones, iTagPro smart tracker in addition to some telematics gadgets that works as a novel identification code. This 15-digit quantity is normally printed either on the underside of the GPS tracking unit or the machine case; you require IMEI to register the GPS tracking device on the fleet management software. Red wire (of GPS system) to one end and the facility source of the car to the opposite finish of a 1Amp fuse. Secure the fuse to the instrument chord with a cable tie. Connect Black wire (-ve) on the harness to Chassis Ground (any bolt or iTagPro smart tracker wire with -ve power). Connect Yellow ignition sense wire to the vehicle’s ignition supply to help monitor ignition ON/OFF events. Please seek the advice of the car wiring diagram to find the ignition wire.
You'll be able to verify the vehicle ignition wire by measuring the vehicle’s working voltage while the engine is working. Once identified, join the ignition wire to the FUSE Box with a 3M Scotchlok so that it'll snap into place and can get it properly seated. Please consult with the connection diagram beneath, iTagPro product for an in depth view of the wires & connectivities. One of the quickest and ItagPro the most effective place to mount a GPS tracking device or a GPS iTagPro smart tracker is under the dashboard or best item finder gadget an exterior location in a horizontal place with a transparent view of the sky. You could experiment with putting the tracking device at completely different areas on the automobile to find out the most effective reception for the specified stage of concealment. If the device has external GPS antenna then place the antenna underneath the dashboard or wherever convenient using double-sided sticky-tape to ensure it’s firmly fastened there. Once you’ve placed the GPS tracker in the automobile, iTagPro portable you’re all set.
Connect the wire socket and GPS/GSM antenna (of these with external antenna) to the GPS gadget. As quickly as the system is powered on, each green LEDs (GPS & communication) will flash on and off while looking for signals. When full sign energy is achieved, each LEDs will repeatedly illuminate. With a purpose to validate performance, we need to ring the GSM cellular number of the SIM. If it rings or responds with a busy observe, you may safely assume that the machine is functioning properly. If there is no response, chances are you'll must re-insert the SIM card and pet gps alternative check the wiring again. Please Log into the platform along with your credentials to verify the gadget communicates with the server. Note: Make sure that the IMEI no’s & cellular no’s you up to date against the autos are appropriate. To keep away from mishaps whereas installation, be certain that the car ignition is turned off earlier than initiating wire connections. It's always advisable to disconnect the appropriate jumpers /connections of vehicle’s power supply in the course of the GPS machine set up; that is to avoid short circuits and wiring damages.
Ensure that the wires stay disconnected whereas mounting/dismounting the machine. Secure all wiring with Scotchlok, cable connectors, and iTagPro smart tracker electrical insulation tapes. Never allow any naked wiring to remain uncovered; connections must be least seen. Ensure additional insulation if wires go through a visible/exterior area, in order to keep away from brief circuit/wiring damages. GPS monitoring units might be mounted in a zone of restricted entry, so none has direct access to the instrument. Keep connecting wires as discreetly as attainable, making it much less visible and onerous to note. For the security of personnel, machine & car, keep away from connecting system wires to the board computer systems (ECU) or control models. Ensure that you fasten wires to other wires/non-transferring elements and not to fasten close to heat emitting and shifting objects as friction/heat emission might trigger sparks resulting in quick circuits. While connecting ignition wire confirm if it’s the actual ignition wire (power supply available only when the ignition is on). Using a multimeter, iTagPro smart tracker check power circulation by turning on/off the engine.